needle valve manufacturer


Quick joint of stainless steel in addition to the stainless steel, copper, aluminum and other materials.

.

Quick joint of stainless steel in addition to the stainless steel, copper, aluminum and other materials. Because material is different, the type and specification of the stainless steel joint are different, can be used in different industries, including gas, carbon dioxide gas, gas and liquid, steam pressure, rare gas, cooling oil temperature and fast connection of semiconductor materials. According to different joints, can be applied to automobile gasoline, gasoline, diesel, frozen oil, gear oil, gasoline fuel oil, water, salt water, acid and alkali liquid, steam, etc material. The pressure of up to 1.65 million mpa, effective temperature in - 54 ℃ to 180 ℃, wide application. But the large current cable is made of stainless steel rapid joint discomfort. As a result of the current skin effect, most of the current in the cable surface circulation. If quick connector makes the cable on the surface, it will lead to very large cable surface resistance. When large current basis, according to joule's law can lead to very large calorific value, there is the risk of damage to the cable.
In everyone's impression, what do you think of the hydraulic transition joint easy to install? If you think so, it would be wrong. Actually with hydraulic transition joints is not so easy as you think, but when you are familiar with is not particularly complex. So, with hydraulic transition joints, should remember that you can't ignore what point? Let's take a look at the following. The first (1) pay attention to the taper hole depth During the installation process, people use joint as the substrate, but many people tend to ignore the depth of the taper hole on the joint, if do not pay attention to this, it is easy to cause leakage, the correct operation should be using the same kind of precast joint, so as to solve the problem of leakage. 2 tube, do not deviate too far when pre-loaded with hydraulic transition 12 needle valve joints, usually to remember to keep the bottom surface smooth, after deburring, cleaning and a series of work can be normal use. At the same time, as far as possible when preloading keep the pipe and the joint body alignment, don't let the pipe found deviation is larger. Once it occurs, it may lead to some things, the seal is SLATE. Should also be pointed out that it should be appropriate. Widely used in the field of energy, railway, traffic, etc, due to the need to ensure the normal use of equipment and facilities, higher requirements to the use of materials and accessories. When need to transition joints, hydraulic transition joints used in these areas. In addition, we can find that it needs to be used in metallurgy, mining, Marine engineering and other fields.
Quick joint of stainless steel in addition to the stainless steel, copper, aluminum and other materials. Because material is different, the type and specification of the stainless steel joint are different, can be used in different industries, including gas, carbon dioxide gas, gas and liquid, steam pressure, rare gas, cooling oil temperature and fast connection of semiconductor materials. According to different joints, can be applied to automobile gasoline, gasoline, diesel, frozen oil, gear oil, gasoline fuel oil, water, salt water, acid and alkali liquid, steam, etc material. The pressure of up to 1.65 million mpa, effective temperature in - 54 ℃ to 180 ℃, wide application. But the large current cable is made of stainless steel rapid joint discomfort. As a result of the current skin effect, most of the current in the cable surface circulation. If quick connector makes the cable on the surface, it will lead to very large cable surface resistance. When large current basis, according to joule's law can lead to very large calorific value, there is the risk of damage to the cable.
Transition joints and other parts must be assembled on the basis of reliable quality. Only in this way can, in the use of superior function, ensure reliable applications. According to the requirement of the joint tightness control assembly is very important.
Because if the transition joints installation is not tight, will lead needle valve manufacturer to the existence of the connector not strong enough. This in the pipeline system, will inevitably lead to leakage problems. For many need to use the function of the connector system, the existence of the leak is not only waste materials, influence the normal operation of the whole system, also can bring security risks.But this is not to say that the transition joints can tighten when assembly, because the installation of transition joint is too loose, not only and install too closely, can cause some bad situation. If you do more fastening operations, has the potential to joint in the case of huge external force a certain amount of damage. Like when the screw is too tight is easy to slip, causing them to once again unable to properly tighten, joint assembly.

995 Uitzichten

Reacties